
How to Winterize Your Chicago Home: 10 Ways to Stay Warm and Cut Heating Bills
2026-11-13

Every winter, thousands of Chicago homeowners pay to heat the street. Not on purpose, of course. Warm air slips out through a drafty window frame, a worn door seal or a cold outlet, and the furnace keeps running to replace it. You feel it as a chill by the couch, and you see it in your heat bills.
That hurts more every year. Last winter, Peoples Gas expected typical bills to rise by $15 to $17 a month, and the average heating bill in Chicago keeps climbing. Older bungalows and two-flats lose the most heat, often through gaps you’d never notice.
The good news: you don’t need a new furnace to stay warm. You need to winterize a home the smart way. Here are 10 ways to do it, from 10-minute DIY fixes to repairs worth leaving to a pro.
Where Your Home Loses Heat: What to Check First
Before you start sealing, spend 20 minutes finding where the cold gets in. Walk through your home room by room and check the usual weak spots:
Windows and doors: gaps around frames, cracked caulk, worn seals, light visible around a closed door.
Outlets and baseboards: cold air on exterior walls and where pipes or cables pass through.
Basement: gaps at the rim joist, around basement windows and exposed pipes.
Attic: thin or uneven insulation, an unsealed hatch.
Outside: cracked caulk, damaged mortar, hoses still connected to outdoor faucets.
Then confirm the leaks with three quick tests. Pick a windy day and turn on the bathroom and kitchen exhaust fans to pull outside air in.
Hand test: move your palm slowly along frames, door edges and outlets. A cool stream of air means a gap.
Incense test: hold a lit incense stick near the same spots. If the smoke wavers or drifts, you’ve found a leak.
Paper test: close a window or door on a sheet of paper and pull. If it slides out easily, the seal is worn.

10 Ways to Winterize Your Chicago Home
1. How to Winterize Windows
Start outside. Check the joint between the window frame and the wall, and replace cracked or missing caulk with an exterior-grade silicone or polyurethane sealant. Do it on a dry day above 40°F, or the caulk won’t cure properly.
Inside, seal the moving parts. On double-hung windows, use V-strip (tension seal) along the sides of the sash and foam tape along the bottom rail. When winterizing a window you never open in winter, removable rope caulk is a fast, cheap fix. For single-pane glass, a winterizing kit for windows (shrink film tightened with a hair dryer) adds an insulating air layer.
When you winterize old windows, don’t skip the basement: fit rigid foam board into the opening or add a window well cover outside. Remove your window AC if you can. When winterizing a window air conditioner you leave in place, use an insulated exterior cover and seal the side panels with foam strips.
Rotted sills, broken sash cords, fogged glass or a sash that won’t lock tight need repair, not caulk. Our window repair team fixes these in one visit.

2. Replace Door Weatherstripping and Add a Door Sweep
Check door weatherstripping on every exterior door, including the back door and the door to an attached garage. Foam or rubber seals that are flattened, cracked or torn should be replaced. Most pull out of a groove in the jamb and press back in.
The gap at the bottom loses the most heat. Weatherstripping for bottom of door comes in two main types: a screw-on door sweep or a U-shaped door bottom that slides over the door edge. Many thresholds also have adjustment screws: raise the threshold until the door closes snugly against it.
Sliding patio doors leak in a different way. Clean the track, replace worn pile weatherstripping on the sliding patio door panel, and adjust the rollers so the door sits tight against the frame when closed.
If a door sags, drags, won’t latch or still leaks after new seals, the problem is the hinges, frame or jamb. Our home repair team can realign or repair it.
3. Insulate Outlets on Exterior Walls
Outlets and switches on exterior walls are small holes in your home’s insulation. To insulate outlets, use pre-cut foam gaskets that fit behind the cover plate. Turn off the breaker, remove the plate, place the gasket and screw the plate back on. It takes about two minutes per outlet.
Insulated electrical outlets work even better with plastic safety plugs in unused sockets, since air also leaks through the slots. Use only foam insulation for outlets made for this purpose. Never stuff fiberglass or loose material into an electrical box.
While the cover plate is off, check the outlet itself. A warm plate, scorch marks, a buzzing sound or an outlet that moves in the wall are signs of loose or damaged wiring and a real fire risk. Don’t add a gasket to an outlet like that. It needs an electrician first.
4. Insulate Pipes and Shut Off Outdoor Faucets
Pipes in unheated basements, crawl spaces, garages and along exterior walls lose heat and can freeze when Chicago drops below zero. Slip polyethylene foam sleeves over exposed hot and cold lines and seal the seams with tape. Near the furnace or water heater flue, use fiberglass pipe wrap instead and keep the required clearance.
Before the first hard freeze, disconnect and drain garden hoses. Close the indoor shut-off valve that feeds each outdoor faucet, then open the faucet outside to drain the remaining water. Add an insulated faucet cover. During cold snaps, open sink cabinet doors on exterior walls so warm air reaches the pipes, and never set the heat below 55°F if you leave home. Read more in our guide on how to prevent frozen pipes in Chicago.
Rust, drips or old galvanized pipes should be fixed before winter. A slow leak in November can become a burst pipe in January. Our plumbing team can inspect and repair them.
5. Seal Gaps Around Pipes, Vents and Baseboards
Look wherever something passes through an exterior wall: plumbing lines, dryer vents, cable and gas lines. Also check baseboards on exterior walls and the rim joist in the basement, where the house sits on the foundation. These hidden gaps often leak more air than a drafty window.
Use the right material for the gap. Caulk works for cracks up to about 1/4 inch. For larger openings, use low-expansion spray foam, which won’t warp frames or trim. Around chimneys and furnace flues, use only fire-rated sealant or metal flashing, since regular foam and caulk are flammable.
Never seal combustion air vents for the furnace or water heater. Gas appliances need that air to burn safely. If you’re unsure which openings are safe to seal, leave it to a pro.
6. Seal the Attic Hatch and Add Insulation
Warm air rises, so the attic is where many homes lose the most heat. Start with the hatch. Add foam weatherstripping around the opening and glue a piece of rigid foam board to the top of the hatch cover. Pull-down attic stairs need an insulated cover box that sits over the opening.
Before adding insulation, seal the air leaks in the attic floor: gaps around light fixtures, plumbing vent pipes, wiring holes and the tops of interior walls. Insulation slows heat, but it doesn’t stop air.
Then check the depth. For Chicago’s climate zone, ENERGY STAR recommends R-60 for an uninsulated attic, or adding R-49 if you already have 3 to 4 inches of insulation. If you can see the tops of the ceiling joists, you need more. Keep insulation away from soffit vents so the attic can still breathe.
If you have a fireplace, keep the damper closed whenever there’s no fire. An open damper works like an open window straight to the roof.
7. Seal Leaky Ductwork
If your home has forced-air heat, ducts carry warm air from the furnace to every room. According to ENERGY STAR, about 20 to 30 percent of that air is lost through leaks, holes and poorly connected ducts in a typical house. In many Chicago homes the ducts run through an unheated basement, so you end up heating the basement walls.
Check every duct you can reach, starting near the furnace, where pressure is highest. Look for separated joints, gaps and old cloth tape that has dried out. Seal seams with UL 181-rated foil tape or duct mastic. Despite the name, regular cloth duct tape doesn’t last on ducts. Then wrap ducts in unheated spaces with duct insulation rated R-6 or higher. Seal first, insulate second.
Many older Chicago homes heat with radiators instead of ducts. In that case, bleed hot-water radiators at the start of the season to release trapped air, and check that the air vents on steam radiators aren’t stuck or leaking.
8. Service Your Furnace Before Winter
A clogged filter forces the furnace to run longer for the same heat. Check it monthly during winter and replace it every one to three months. A MERV 8 to 11 filter balances clean air and good airflow for most homes.
Schedule furnace maintenance in Chicago in early fall, before HVAC companies get booked up with the first cold snap. A proper tune-up includes cleaning the burners and flame sensor, checking the igniter and blower, and inspecting the heat exchanger for cracks. A cracked heat exchanger can leak carbon monoxide.
That’s also why working CO detectors matter. Illinois law requires a carbon monoxide alarm within 15 feet of every room used for sleeping. Test yours when you service the furnace.
If your furnace is more than 15 years old, needs frequent repairs, or your bills keep rising after you’ve sealed the house, it may be time to replace it. According to the U.S. Department of Energy, older furnaces run at 56% to 70% efficiency (AFUE), while modern high-efficiency models reach 90% to 98.5%. In other words, an old furnace can waste up to a third of the gas you pay for.
9. Set Your Thermostat the Smart Way
The U.S. Department of Energy recommends about 68°F while you’re home and awake. Turning the thermostat back 7 to 10 degrees for 8 hours a day, while you sleep or are at work, can save up to 10% a year on heating and cooling.
A programmable or smart thermostat makes this automatic. According to ENERGY STAR, a certified smart thermostat saves about $50 to $100 a year on average. Set it to start warming the house about 30 minutes before you wake up or come home.
Don’t crank the heat to 80°F to warm up faster. A furnace delivers heat at the same speed no matter the setting; it just runs longer and overshoots. If you have a heat pump, use smaller setbacks, or the expensive backup heat may kick in. Leaving for a trip? Don’t set the heat below 50 to 55°F, to protect your pipes.
10. Use Ceiling Fans and Curtains, Keep Vents Clear
Most ceiling fans have a direction switch on the motor housing. In winter, set the blades to turn clockwise at low speed. This pushes the warm air that collects near the ceiling back down without creating a cold breeze.
Use your windows as free heaters. Open curtains on south-facing windows on sunny days, then close them at sunset. Thermal or lined curtains that reach the floor hold in noticeably more heat than thin blinds.
Finally, make sure heat can reach the room. Move sofas, beds and long drapes away from supply vents and radiators, and don’t cover floor registers with rugs. Avoid closing more than one or two vents in unused rooms. Forced-air systems are designed for a certain airflow, and closing too many vents raises duct pressure and pushes more warm air out through leaks.
When to Call a Pro
A draft is a symptom, not always the problem. If new weatherstripping doesn’t stop it, the cause is usually a sagging frame, rot or worn hinges, and anything involving gas lines, wiring or furnace venting is a safety issue, not a DIY job. Use the table below as a rule of thumb: fix the seal yourself, call a pro when the seal isn’t the problem.

Get Your Home Ready for Winter with Fix Pro
Looking for home winterization services near you? Fix Pro has been helping Chicago homeowners for 6 years, with more than 250 jobs completed. Our founder, Oleh, still goes out to jobs himself and personally oversees every project, so your home is in experienced hands from the first inspection to the last bead of caulk.
We start with a full winter walkthrough of your home, find every weak spot, and fix most of them in the same visit: drafty windows, leaky doors, outlets and plumbing.
Don’t wait for the first deep freeze. Call +1 (312) 721-0843 or book your visit online.
FAQ
How can I save on my heating bill?
Start with air sealing and insulation. On average, they cut heating and cooling costs by about 15%, and by about 16% in cold climates like Chicago’s. Then add the cheapest fixes, like caulk, weatherstripping and the right thermostat settings, to lower your heating bill without buying new equipment.
How much does it cost to winterize a home?
Most DIY steps need only inexpensive hardware-store supplies: caulk, weatherstripping, foam gaskets and pipe sleeves. The cost of winterizing a home with a pro depends on what needs repair. Re-sealing doors and windows is a small job, while fixing rotted frames, wiring or plumbing takes more work. A walkthrough first shows exactly what your home needs.
When should I winterize my house in Chicago?
Aim for October through mid-November, before nights stay below freezing. Exterior caulk needs a dry day above 40°F to cure properly, so outdoor sealing is easier early in the fall. Indoor jobs like weatherstripping and outlet gaskets can be done any time.
Is it worth replacing old windows to save on heating?
Not always. Many drafty windows in Chicago bungalows only need new caulk, weatherstripping or a sash repair, which costs far less than replacement. Replacement makes sense when frames are badly rotted or the glass seal has failed.
Can I get help paying my heating bill in Chicago?
Yes. Income-qualified households can apply for LIHEAP, the federal heating assistance program, and both Peoples Gas and ComEd offer income-based discounts. Illinois also limits utility disconnections for eligible customers who heat their homes with gas or electricity from December 1 to March 31.
